New HBZ high voltage LED taillights. Single round taillight/Brakelight is for the true buggy/prerunner look! The new LED’s mount to anywhere you can stick the 3M adhesive aluminum body. Comes with a clear cover that protects the 15 LED’s from damage. These are high voltage LED’s and they are made to run off a separate power source in order to leave your stock battery free for its intended use. The kit comes with a convenient 9vlt adapter that can be wired in or you can use the HBZ li-po battery or any other power source up to 12vlts. The kit also comes with a resistor and a kill switch that allows the user to have a taillight and a brake light. User must understand simple electronics to fallow instructions and solder wires.

Light up the night with the new LED Light with Battery Indicator Set for the Baja 5B! This light set has everything you need to add lights to the stock light housings on the Baja 5B. In addition to lighting up the night, the light set also flashes to alert you when your receiver batteries are low, giving you extra warning when a recharge is needed. The set includes super bright blue LED Lights, a Light Setup Unit, and an Extension Wire Fork. Everything in the set is clearly labeled and pre-wired with plugs for quick and simple installation! HPI part # 337

The HPI D-Box Drift Assist Adjustable Stability Control System works on all HPI Racing and HotBodies vehicles. This system was specially developed for RC cars to assist in getting the perfect drift angle around the turns, but further research yielded benefits for every vehicle! From the Micros to the Baja, this Adjustable Stability Control System will assist your driving and overall car control.
All of this control is achieved with an ultra-small yaw control sensor that allows the Adjustable Stability Control System to detect your tail sliding, and the optimized automatic counter-steering prevents your car from spinning. It comes with a gain control function to adjust counter-steering according to the track surface condition and / or the amount of control assistance you are looking for.
Just connect the Adjustable Stability Control System to the steering servo and it will electronically assist your driving. The device weights only 6.7g. The Stability Control System / D-BOX is connected between the receiver and the steering servo and can be used with all radio gear using Futaba style connectors. This is the ideal hop-up part for the Sprint 2 - Stage-D Kit (#30401 and #30402) and #33432 Stage-D Conversion Set for the Nitro 3, and will also work in offroad trucks and buggies. Note: The Adjustable Stability Controls may be an unfair advantage and not legal for racing, check your local rule book. Yes, it is that good! HPI part # 80588

This is a new-style Futaba replacement antenna for all three surface receivers R603FS R603FF and R604FS, the futaba antenna part number is HSP79452
This antenna is much easier to replace than the older style. The new antenna is coaxial and has a small clip at the base so it just snaps on and off. This is nice since it will make it a simple do-it-yourself antenna fix.

MRCs New Super Brain 977 Charger Takes the Words "User Friendly" to New Heights. The newest addition to the Super Brain family of chargers, the 977 Pro offers latest technology with many features for those who want more control over their batteries. This AC/DC charger with dual output and discharge function starts where other chargers can only hope to get to. Feature rich, yet very affordable, its US Patent 6,218,808 B1 MicroPeak technology safely and effortlessly charges and discharges 1-8 cell nickel cadmium, nickel metal-hydride batteries as well as gel-cell, and lead acid batteries. A special, practically "foolproof" setting for 1-3 cell lithium ion /polymer batteries makes it safe & easy to put maximum energy back into your packs. The big 10 Amp AC power supply and the Super Brain 977 are both fan cooled to keep components cool during continuous charging cycles. Simultaneous charging & discharging of dissimilar packs has been carried over from MRC's highly successful Super Brain 969; charge two batteries at the same time even if they are different voltages and/or battery types. The discharge function allows you to get the most out of your batteries, increasing battery life and thereby saving the cost of purchasing new batteries. The large LCD display puts a wealth of information at your fingertips: battery status, battery voltage, charge rate, peak threshold in mV, capacity in MAh, number of cells in the pack, and charging time in minutes. The 977's selectable charge rate with 0.10 amp increments allows you to use charge rates from 0.20 amps all the way up to a powerful 5.0 amps. Similarly, you can select an appropriate and safe discharge rate with 0.10 amp increments from 0.20 down to a rapid 4.0 amps. The peak threshold can be selected in 5mV increments from 5 to 50 mV. The Super Brain 977 uses Digital Signal Processing to filter out noise and provide a high level of measurement accuracy and along with its 12-bit Analog to Digital converter the chargers measurement resolution is always first rate.
AC/DC delta peak charger with patented MicroPeak Technology
Dual independent outputs for added versatility
Discharge function allows you to get the most out of your batteries
Large LCD screen shows: battery voltage, charge rate, peak threshold, capacity, number of cells in pack & elapsed time
Charges NiCd, NiMH, Li & Pb batteries
For 1~8 cells any capacity battery
Selectable charge rate with 0.1 amp increments
Selectable delta peak voltage thresholds in 5mV increments
Cooling fan keeps components cool for continuous charging
12-bit Analog-to-Digital converter greatly improves measurement resolution
Digital Signal Processing filters out noise and improves voltage accuracy

The Killer Bee was designed to be the ultimate kill switch for your large scale gas RC.

2 cell LiPo compatible
Shortened pigtail leads
Upgraded firmware
Remote status LED output
Alarm buzzer output
Auto Engine Kill
Manual Engine Kill

The Killer Bee will automatically kill the engine during: lost radio reception, low battery, bad connection, or total power loss. You can also kill the engine anytime you want via the transmitter's 3rd channel switch.

Without a kill switch a radio glitch, fried servo, or stuck throttle linkage can result in a runaway, which can cause expensive suspension and chassis damage and even a blown engine. A Killer Bee will keep this from happening to your RC.

This kit comes with heat resistant wiring that is soldered to a new CY push button kill switch. Installation is easy.

LED Lights and Buzzers can be added onto this kit for an extra charge. This is kit #3 on the Killer RC website. By adding the LED and/or buzzer you end up with a kit #4 or #5

Modified Pico Kill Switch. This is a stock Dimension Engineering Pico Switch that has been modified for large scale R/C use. This amazing little gadget will do everything you want in a failsafe. The engine will kill if:

Transmitter is turned off
Transmitter is out of range
Servo wire is cut

3rd channel switch is activated

 

Comes with detailed instructions.

Custom Street Toyz billet headlight pods for HBZ LED’s. Made to replace the stock plastic pods but allow use of the popular 15 place high voltage LED pods. Choose these for either their cool looks or the strength. Either way you will be happy with this quality product from Custom Street Toyz. Uses threaded mounts with nuts to allow the user to adjust the mounting angle of the lights. Works with HBZ 15 place LED’s ONLY. Will NOT work with hpi or other aftermarket LED boards. Comes complete with all needed hardware and instructions.